Description
**METRIC VERSION**
This specification is a Reference Specification that the Engineer or Architect can make applicable to any construction project by citing it in the Project Specifications. The Architect/Engineer supplements the provisions of this Reference Specification as needed by designating or specifying individual project requirements.
The document covers materials and proportioning of concrete; reinforcing and prestressing steels; production, placing, finishing, and curing of concrete; and formwork design and construction. Methods of treatment of joints and embedded items, repair of surface defects, and finishing of formed and unformed surfaces are specified. Separate sections are devoted to architectural concrete, lightweight concrete, mass concrete, prestressed concrete, and shrinkage-compensating concrete. Provisions governing testing, evaluation, and acceptance of concrete as well as acceptance of the structures are included.
Keywords: admixture; aggregate; air entrainment; architectural concrete;
cement; cementitious materials; cold weather; compressive strength;
concrete; concrete construction; concrete durability; concrete slab; consolidation;
conveyor; curing; density; exposed-aggregate finish; finish; floors;
formwork; grout; grouting; hot-weather; inspection; joint (construction,
contraction, and isolation); lightweight concrete; mix; mixture proportion;
placing; prestressed concrete; prestressing steel; reinforced concrete; reinforcement; repair; reshoring; shoring; shrinkage-compensating concrete;
specification; subgrade; temperature; test; tolerance; water-cementitious
material ratio; welded wire reinforcement.
Table of Contents
Section 1—General requirements
1.1—Scope
1.1.1— Work specified
1.1.2— Work not specified
1.2—Definitions
1.3—Reference standards and cited publications
1.3.1—Reference standards
1.3.2—Cited publications
1.3.3—Field references
1.4—Standards-producing organizations
1.5—Submittals
1.5.1—General
1.5.2—Testing agency reports
1.6—Quality assurance
1.6.1—General
1.6.2—Testing agencies
1.6.3—Testing responsibilities of Contractor
1.6.4—Testing responsibilities of Owner’s testing agency
1.6.5—Tests on hardened concrete in-place
1.6.6—Evaluation of concrete strength tests
1.6.7—Acceptance of concrete strength
1.6.8—Field acceptance of concrete
1.7—Acceptance of structure
1.7.1—General
1.7.2—Dimensional tolerances
1.7.3—Appearance
1.7.4—Strength of structure
1.7.5—Durability
1.8—Protection of in-place concrete
1.8.1—Loading and support of concrete
1.8.2—Protection from mechanical injury
Section 2—Formwork and formwork accessories
2.1—General
2.1.1—Description
2.1.2—Submittals
2.2—Products
2.2.1—Materials
2.2.2—Performance and design requirements
2.2.3—Fabrication and manufacture
2.3—Execution
2.3.1—Construction and erection of formwork
2.3.2—Removal of formwork
2.3.3—Reshoring and backshoring
2.3.4—Strength of concrete required for removal of
formwork
Section 3—Reinforcement and reinforcement
supports
3.1—General
3.1.1—Submittals, data, and drawings
3.1.2—Materials delivery, storage, and handling
3.2—Products
3.2.1—Materials
3.2.2—Fabrication
3.3—Execution
3.3.1—Preparation
3.3.2—Placement
Section 4—Concrete mixtures
4.1—General
4.1.1—Description
4.1.2—Submittals
4.1.3—Quality control
4.1.4—Materials storage and handling
4.2—Products
4.2.1—Materials
4.2.2—Performance and design requirements
4.2.3—Proportioning
4.3—Execution
4.3.1—Measuring, batching, and mixing
4.3.2—Delivery
Section 5—Handling, placing, and constructing
5.1—General
5.1.1—Description
5.1.2—Submittals
5.1.3—Delivery, storage, and handling
5.2—Products
5.2.1—Materials
5.2.2—Performance and design requirements
5.3—Execution
5.3.1—Preparation
5.3.2—Placement of concrete
5.3.3—Finishing formed surfaces
5.3.4—Finishing unformed surfaces
5.3.5—Sawed contraction joints
5.3.6—Curing and protection
5.3.7—Repair of surface defects
Section 6—Architectural concrete
6.1—General
6.1.1—Description
6.1.2—Submittals
6.1.3—Quality assurance
6.1.4—Product delivery, storage, and handling
6.1.5—Project conditions
6.2—Products
6.2.1—Materials
6.2.2—Performance and design requirements
6.3—Execution
6.3.1—Preparation
6.3.2—Proportioning concrete mixtures
6.3.3—Consolidation
6.3.4—Formwork monitoring
6.3.5—Formwork removal
6.3.6—Repair of tie holes and surface defects
6.3.7—Finishing
Section 7—Lightweight concrete
7.1—General
7.1.1—Description
7.1.2—Submittals
7.1.3—Product delivery, storage, and handling
7.2—Products
7.2.1—Aggregates
7.2.2—Performance and design requirements
7.2.3—Mixtures
7.2.4—Batching and mixing
7.3—Execution
7.3.1—Consolidation
7.3.2—Finishing
7.3.3—Field quality control
Section 8—Mass concrete
8.1—General
8.1.1—Description
8.1.2—Submittals
8.2—Products
8.2.1—Materials
8.2.2—Performance and design requirements
8.3—Execution
8.3.1—Placement
8.3.2—Curing and protection
Section 9—Prestressed concrete
9.1—General
9.1.1—Description
9.1.2—Submittals
9.1.3—Quality control
9.1.4—Product delivery, handling, and storage
9.2—Products
9.2.1—Materials
9.2.2—Proportioning of concrete and grout mixtures
9.3—Execution
9.3.1—Inspection
9.3.2—Preparation
9.3.3—Placement
9.3.4—Tensioning
Section 10—Shrinkage-compensating concrete
10.1—General
10.1.1—Scope
10.1.2—General requirements
10.1.3—Submittals
10.2—Products
10.2.1—Materials
10.2.2—Performance and design requirements
10.2.3—Proportioning
10.2.4—Reinforcement
10.2.5—Isolation-joint filler materials
10.3—Execution
10.3.1—Reinforcement
10.3.2—Placing
10.3.3—Isolation joints
10.3.4—Curing