Table of Contents
Chapter 1—Introduction and scope
1.1—Introduction
1.2—Scope
1.3—Units of measurement
Chapter 2—Notation and definitions
2.1—Notation
2.2—Defintions
Chapter 3—General requirements
3.1—Test organization
3.2—Variables and options
3.3—Test requirements
3.4—Assessment for multiple anchor element types for adhesive anchors
3.5—Assessment for alternate drilling methods
Chapter 4—Requirements for test specimens, anchor installation, and testing
4.1—Testing by ITEA and manufacturer
4.2—Test samples
4.3—Concrete for test members
4.4—Requirements for test members
4.5—Anchor installation
4.6—Drill bit requirements
4.7—Test methods
4.8—Tests in cracked concrete
4.9—Changes to products
Chapter 5—Requirements for anchor identification
5.1—Basic requirements
5.2—Verification
5.3—Fingerprinting adhesive materials
5.4—Packaging
Chapter 6—Reference tests
6.1—Purpose
6.2—Required tests
6.3—Conduct of tests
Chapter 7—Reliability tests
7.1—Purpose
7.2—Required tests
7.3—Conduct of tests
7.4—Reliability tests
7.5—Sensitivity to hole cleaning—dry concrete
7.6—Sensitivity to hole cleaning—saturated concrete
7.7—Sensitivity to hole cleaning—water-filled hole
7.8—Sensitivity to hole cleaning—submerged concrete
7.9—Sensitivity to mixing effort
7.10—Sensitivity to installation in water-saturated concrete
7.11—Sensitivity to installation in water-filled hole—saturated concrete
7.12—Sensitivity to installation in submerged concrete
7.13—Sensitivity to crack width—low-strength concrete
7.14—Sensitivity to crack width—high-strength concrete
7.15—Sensitivity to crack width cycling
7.16—Sensitivity to freezing and thawing
7.17—Sensitivity to sustained loading at standard and maximum long-term temperature
7.18—Sensitivity to installation direction
7.19—Torque test
Chapter 8—Service-condition tests
8.1—Purpose
8.2—Required tests
8.3—Conduct of tests
8.4—Tension tests in uncracked and cracked concrete
8.5—Tension tests at elevated temperature
8.6—Tension tests with decreased installation temperature
8.7—Establishment of cure time at standard temperature
8.8—Durability assessment
8.9—Verification of full concrete capacity in a corner
8.10—Determination of minimum spacing and edge distance to preclude splitting
8.11—Tests to determine shear capacity of anchor elements with nonuniform cross section
8.12—Simulated seismic tension tests
8.13—Simulated seismic shear tests
Chapter 9—Supplemental tests
9.1—Round-robin tests
9.2—Tests to determine minimum member thickness
Chapter 10—Assessment of anchors
10.1—Analysis of data
10.2—Normalization of anchor capacities for measured concrete bond and steel strengths
10.3—Establishing characteristic values
10.4—Assessment of characteristic tension capacity associated with concrete breakout and pullout
10.5—Assessment of steel tension capacity
10.6—Assessment of steel shear capacity
10.7—Assessment of minimum member thickness
10.8—Assessment of maximum tightening torque
10.9—Assessment of behavior under crack cycling
10.10—Assessment of freezing-and-thawing behavior
10.11—Assessment of sustained load behavior
10.12—Assessment of performance associated with installation direction
10.13—Assessment of performance at elevated temperature
10.14—Assessment of performance with decreased installation temperature
10.15—Assessment for cure time at standard temperature
10.16—Assessment of durability requirement
10.17—Assessment of performance in corner test
10.18—Assessment of performance in minimum spacing and edge distance test
10.19—Assessment of performance under seismic tension
10.20—Assessment of performance under seismic shear
10.21—Establishment of hole cleaning procedures
10.22—Establishment of on-site quality control and installation conditions
10.23—Assessment based on installation and environmental conditions
10.24—Assessment for fire exposure
Chapter 11—Data presentation
11.1—General requirements
11.2—Contents of evaluation report
11.3—Data presentation
Chapter 12—Independent testing and evaluation agency requirements
12.1—General requirements
12.2—Certification
Chapter 13—Quality control requirements
13.1—Quality assurance program
13.2—Quality control manuals
13.3—Special inspection
Chapter 14—References
14.1—Referenced standards and reports
14.2—Cited reference